- 您现在的位置：买卖IC网 > Sheet目录532 > VIPER-S2 (RF Solutions)REMOTE CONTROL SYSTEM FM 2CH
VIPER Remote Control Systems
Pairing a Transmitter to a Receiver
Each transmitter has a unique identity. Each time a transmitter Switch is operated, it emits a secure
RF signal. The Receiver can learn this signal and allocate to any of its outputs.
The only limitation is that each receiver has a maximum memory for up to 40 pairings, these can be from
the same or any number of transmitters.
Hint: the same transmitter may be taught to different receivers to create ‘master keys’.
VIPER- S1 / VIPER- S2 / VIPER- S4 (12- 30Vdc Receivers)
To Learn a New Transmitter switch follow this procedure
Any transmitter button can be learnt to one or many of the receiver output relays.
Each button must be learnt to each relay individually by following this procedure:
1.
Select the receiver output relay to learn to:
2. Briefly press the receiver Learn switch (S2) once
3.
4.
The Learn LED will flash once to indicate output relay 1 is selected
After the LED stops flashing, press the Learn switch again to select the next relay channel
5. Repeat step 2 until the required output relay is selected.
6.
7.
8.
9.
Press the button on the transmitter you want to learn to the relay output.
The Learn LED will then illuminate, press the same transmitter button again.
The Learn LED will then flash to indicate learning is complete.
The transmitter button will now operate the relay.
Erasing Receivers Memory
1.
2.
Press and hold the receiver Learn Switch for approx 10 seconds.
When the Learn LED turns OFF all memory is erased
NOTE: You cannot erase individual Tx encoders
Configuring Receiver Outputs
The Jumper links configure the outputs to be Momentary or Latching.
The Jumper links are made / removed by the small link ‘cap’ placed over the pin header.
Link Positions
Relay Outputs
LK1
Closed
Closed
Open
Open
LK2
Closed
Open
Closed
Open
RLY 1
Mom
Mom
Mom
Latch
RLY 2
Mom
Mom
Latch
Latch
RLY 3
Mom
Latch
Latch
Latch
RLY 4
Mom
Latch
Latch
Latch
(The configuration shown in the picture above represents the third row of the table)
DS VIPER-4
?2009 REG No 277 4001, Lewes, England. Page 4
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
VKM40-06P1
MOSFET H-BRIDGE 600V ECO-PAC2
VKM60-01P1
MOSFET H-BRIDGE 100V ECO-PAC2
VMK165-007T
MOSFET MOD DUAL COMMON TO-240AA
VMK90-02T2
MOSFET MOD DUAL COMMON TO-240AA
VMM300-03F
MOSFET MOD PHASE LEG 300V Y3-DCB
VMM45-02F
MOSFET MOD PHASE 200V TO-240AA
VMM650-01F
MOSFET MOD PHASE LEG 100V Y3-LI
VMM85-02F
MOSFET MOD PHASE LEG 200V Y4
相关代理商/技术参数
VIPER-S2M
制造商:RFMD 制造商全称:RF Micro Devices 功能描述:VIPER Remote Control Systems
VIPER-S4
功能描述:REMOTE CONTROL SYSTEM FM 4CH RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:- 标准包装:5 系列:MultiModem® iCell 功能:收发器，HSPA，调制解调器 调制或协议:GPRS，GSM，EDGE 频率:850MHz，900MHz，1.8GHz，1.9GHz 应用:- 接口:RS-232，USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V，USB 其它名称:881-1125
VI-PJ0ZZ-EZZ
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:25 to 600 Watts DC-DC Converters Single, Dual, Triple Output Chassis Mount
VIPJ504CXY
制造商:VICOR 功能描述:*
VIP-JVC/05
制造商:OSRAM SYLVANIA 功能描述:Replacement DLP Lamp - Bare Bulb For P-VIP 100-120/1.0 P20
VIP-LCD-KIT
制造商:CORNING CABLE SYSTEMS 功能描述:COMPLETE VIDEO INSPECTION KIT WITH LCD DISPLAY HARDWIRED WITH VIDEO PROBE, HOUSE
VIP-M07-ADIS
功能描述:AUDIO & BODY 制造商:stmicroelectronics 系列:* 零件状态:在售 标准包装:1
VIPRC
制造商:Speco Technologies 功能描述:Remote Control for Speco Cameras with Motorized Zoom